![]() December 18, 2016 - Morton, Illinois 2016 Truck Report (1990 F150) Odometer on December 18, 2016: 167,917 miles. This is 8670 miles since this time last year, and 55,171 miles since July 24, 2010, when purchased. Gas mileage this year was 17.1mpg - up six-tenths from last year. Service (not including oil changes) March 1: New rear hangers and shackles for rear springs, new rear axle brake lines and all front brake lines and hoses by Sancken Automotive ($820.27). September 28: Four new tires (Cooper Discoverer HT P235/75R15) from Farm & Fleet ($511.70). October 5: Replaced water pump, radiator hoses, heater hoses, hose clamps, thermostat, temperature sensor, antifreeze, serpentine belt, and windshield washer pump ($157.17). October 12: New outer tie rod ends (both sides) and front wheel alignment by Sancken Automotive ($231.13). October 19: Removed old trailer wiring harness. Replaced truck bed rear light assembly ($6.84). December 5: Replaced left headlight bulb ($9.60). Repairs this year started off with replacement of the rear brackets and shackles for the rear springs, after figuring out where a clicking sound I was hearing was coming from. Fortunately, a replacement kit is available. I thought about doing this replacement myself, but I'd read that getting the bolt out of the spring bushing is not easy. ![]() March 1 - original and replacement left rear hanger and shackle The truck did well through the summer, even providing me with a trouble-free trip to and from Springfield, Missouri. My sister Laurie reported that the truck started right up after sitting four weeks, and she didn't stall it once during her nineteen-mile trip to get me and my busted bike at the end of my Kansas/Oklahoma bicycle trip (http://www.crazyguyonabike.com/doc/page/?page_id=480299). The tires were due for replacement this fall, and Farm & Fleet took care of that on September 28. I received a good deal on those, with a one-day ten-percent-off discount, plus a $50 rebate card. Apparently, they have a new way for balancing the wheels now, which doesn't involve using lead weights. ![]() September 28 - a new way to balance a wheel (using 1/4 OZ FE weights) Shortly after getting the tires, I was hearing belt noises, and noticed that the high-quality serpentine belt I installed last year was getting chewed up along its edge. It took me a few days to figure out what was causing that. Certainly, if the water pump was going bad, I'd be seeing an antifreeze leak. Finally, I tried wiggling the pump shaft, which produced a good leak when I pulled up. I've changed water pumps before, so figured I could do this myself. The only concern I had was getting the fan clutch off. It's held on by a left-hand threaded nut. The problem is keeping the water pump shaft still so torque can be applied to the nut. Internet research provided the answer for this. There is a special wrench for holding the shaft, but it reportedly breaks more often than it works. However, there was also a YouTube video by a fellow who used a chain to keep the shaft from turning. That seemed like a good idea to me, and it worked very well, using the chain from an old bicycle lock I have. The rest of the project was routine. ![]() October 5 - fan clutch removal, per internet information ![]() October 5 - thermostat housing and water pump mounting locations ![]() October 5 - new water pump and gasket ready for install ![]() October 5 - new water pump installed My father-in-law hauled a load of firewood for us again this year. He likes driving the truck. ![]() October 11 - firewood Christmas present from my in-laws I finally took care of one low-priority truck project that has been bugging me for a long time. The previous owner-installed rear bed light was intermittent, usually taking several presses of its push button to get it to light. And since it was push-button activated, if it didn't light, I was never really sure if I left the switch in its off state. Replacing the push-button switch with a toggle switch I had corrected that uncertainly, but hadn't fixed the intermittency. A new fixture - with an improved bulb socket - made a completely reliable unit. ![]() October 19 - new light for bed, with improved switch |