![]() December 11th, 2019 - Metamora, IL 2019 Truck Report (1990 F150) Odometer on December 18th, 2019: 190,206 miles. This is 7902 miles since this time last year, and 77,457 miles since July 24th, 2010, when purchased. Gas mileage this year was 16.3 mpg - up 2/10 mpg from last year. Service this year: March 22nd: New exhaust pipe, muffler, tail pipe by Rogers' A1 Custom Muffler and Brake, Springfield, MO, ($178.37). April 10th: Changed oil and oil filter. Greased ball joints and U-joints. Replaced air filter, oil pan gasket ($85.11). April 13th: Replaced crankcase filter ($6.20). April 24th: Replaced oil pressure sender. Tightened push rod cover bolts ($18.18). May 17th, 18th, 19th: Sanded and painted rusty spots on oil pan and mounting rails. Replaced oil plug washer, push rod cover gasket (rubber), starter, spark plugs ($102.78). May 21st: Replaced push rod cover gasket (cork) ($18.18). May 24th, 25th, 27th: Removed and cleaned oil pan gasket and reinstalled using RTV sealant at rear corners (per directions). Replaced oil plug washer (again) ($0). June 8th: Cleaned area near rust hole in oil pan and smeared on RTV sealant. September 25th: Disconnected dome/cargo light wire (BK/PK) at connector behind left kick panel. September 28th: Repaired glove box latch. Disconnected glove box light. October 9th: Removed stainless steel screws holding wheel center (hub) caps and replaced screws with steel bolts ($0). October 16th: Rotate and balance tires by Farm & Fleet ($0). November 6th: Greased ball joints and U-joints. November 20th: Replaced tailgate handle, right front turn signal lamp, wipers. Tightened hose clamps, oil pan bolts ($37.53). The 1st item to get attention this year was the exhaust system. I'd driven to Springfield, MO, to visit my sister and brother-in-law in March. Noticing my loud exhaust, my sister mentioned their nextdoor neighbor runs a muffler shop. A visit to his shop fixed me up at a "Family and Friends" discount price. ![]() March 22nd - new exhaust During my yearly oil change, I noticed the sad condition of my oil pan gasket. The trouble with oil pan work on this engine is that, unless the engine is lifted off its mounts, there isn't enough clearance to remove the pan. However, the pan will drop down a few inches with the engine in place. I'd read that a new gasket could be installed with the pan this way, so went that route. It was hard to keep the new gasket clean during install, since I had the gasket inside the pan to fish it around the oil pump intake pipe. What surprised me as I was doing this work was seeing so many rusted areas on the outside of the pan. At one spot near the bolt hole flange there was so much metal gone after scraping rust away that I thought there might be a pinhole there. After a closer look, I concluded there wasn't. A few days later there was still an oil leak. I thought this time it was from either the push rod cover gasket or the oil pressure sender. Replacement of the oil sender (and testing the original) showed the original one was OK. Previous tightening of the push rod cover bolts hadn't helped the leak in that area. I set aside a weekend for replacing the push rod cover gasket and painting the rusted areas on the oil pan. This time I removed the starter for better access to the oil pan, and was alarmed when I saw the way the starter pinion gear had been chewing away at the flywheel teeth. That prompted a trip to Pekin for a new starter. Push rod cover gasket replacement went OK, and I added replacing spark plugs to the "done list" as well. A few days later I realized the push rod cover gasket was leaking worse than before. So that gasket got replaced again - this time with one made of cork (instead of rubber). A few days later there was still oil leaking from somewhere! I hadn't followed the new oil pan gasket instructions exactly when I'd installed it, so figured I needed to remove it and put RTV sealant where the instructions said to (at the rear corners). This time I was able to keep the gasket clean - by stretching it over the outside of the pan (why didn't I do that the 1st time?!). A few days later we're still leaking oil! Only one reason left: there is a pinhole at the flange, just too small for me to see! I smeared RTV at the spot and was finally leak-free (the next day when the sealant was dry)! ![]() April 10th - original oil pan gasket. A friend at work said, "Can you say extrusion?" ![]() May 25th - oil pan painted and with new gasket ![]() May 19th - chewed up flywheel ![]() May 19th - new starter motor My tire rotation and balance was delayed a week after Farm & Fleet reported they couldn't get the screws loose that hold the wheel center hub caps on. A lot of penetrating oil and patience is what that took. The tailgate latch failed at an inopportune time for my father-in-law. He had a load of firewood in the truck and had to unload it up-and-over the tailgate, since it was stuck up! Repair access to this latch is from the inner side of the tailgate behind a removable panel. However, I couldn't initially get to the panel because of the section of the bedliner that is attached to the tailgate. Removal of that required loosening the topper and moving it forward far enough to clear the tailgate. And loosening the topper required removal of the corroded topper-holding c-clamp bolts. With the use of penetrating oil, this project proceeded forward one step at a time. Fortunately, NAPA in town had a replacement handle in-stock. And there was another benefit from this project. The topper's rear window now latches again, since I slid the topper back a little further than it had been - past where the tailgate had kept it from closing all the way. ![]() November 20th - broken (rusted) tailgate handle There were good times driving this year. The truck engine is running great, and I enjoyed my long trips to Springfield, MO, and Lincoln, Nebraska, The truck started right up after sitting four weeks at the Lincoln Airport. The wheels were locked up, but not for long. ![]() September 1st - after sitting four weeks in Lincoln, Nebraska ![]() October 24th - my firewood load (a gift from my in-laws) ![]() November 6th - hauling brush to Morton's yard waste pile ![]() January 12th - hauling freezer-proof shelving |